​Kirkwood is a suburb of St. Louis, Missouri. As of 2010, the city population was 27,540.  The city is named for James Pugh Kirkwood and was founded in 1853.

• Frank Lloyd Wright House in Ebsworth Park
• Kirkwood Park
• Save the Geyer Inn
• Stages Saint Louis
• Emmenegger Nature Park​

​In urban areas, a fire lane is marked near a parking lot near any building. Normal traffic is not allowed to park in the fire lanes to make sure that in case of any emergency the access to safety equipment is done without any hindrance. These lanes are also defined as a passageway to access roads that allow fire department vehicles to pass through easily.

​When a fire lane is designed in any area, there are some requirements that need to be fulfilled first. Since fire trucks and other fire department vehicles are huge, therefore, some adjustments, need to be made for them. Fire lanes also provide a clear space to escape from. Consequently, they need to wider for buildings with large occupancy. 

Fire lane markings are required in various locations depending on the land which is being used. These markings are also required for specific fire apparatus access features like turnarounds. The fire department access should be twenty-six feet wide or less on both sides of the road. One side of the fire department access roadways with widths which is greater than twenty-six feet and can go up to thirty-two feet.
​
There are four ways to mark the fire department turnaround when needed for a specific site. The entrance of the turnaround is marked differently depending upon the width of the roadway which can or cannot be based on the zone of the site. Apart from marking the parking area for the fire lane, installing signs are also a requirement. 

​The curbs which are designated to be a part of the fire lane area are required to be marked with yellow paint. The pavement in the area which is designated as a fire lane should have written “NO PARKING FIRE LANE” on it. The complete area which falls under the Fire Lane should be painted parallel with the curb and should be at a distance of at least three meters from it. It is important to keep in mind that while painting the words “No Parking Fire Lane” on the pavement, all the letters of the sentence should be written in block letters. The height of each letter should be at least 24 inches, and the brush stroke should not be less than 4 inches. 

CALL TODAY FOR A FREE QUOTE
Striping Parking Lots For Kirkwood and the Entire St. Louis Metropolitan Area
(314) 582-8849
Cities and Towns We Serve Around St. Louis:

​Ballwin, Brentwood, Chesterfield, Clarkson Valley, Clayton, Creve Coeur, Des Peres, Frontenac, Glendale, Grantwood Village, Kirkwood, Ladue, Manchester, Oakland, Olivette, Richnd Heights, Rock Hill, Warson Woods, Webster Groves, Wildwood

​Wildwood is a suburb of St. Louis, Missouri. As of the 2010 census, the population was 35,517.
​
Wildwood is the home to a lot of trails, parks, and reserves.  Wildwood is located near Hidden Valley Ski Resort and Six Flags St. Louis

• Hidden Valley Ski Resort
• Six Flags Saint Louis
• Wildwood Community Park
• Rockwoods Reservation
• Bluff View Trail
• Dr. Edmund A. Babler Memorial State Park

​
How Pavement Markings Keep People Safe In Your Parking Lot
 
When entering a parking lot, customers may feel confused about how to park a car properly. If there are no visible navigation arrows or traffic signs, it can even cause car accidents. Pavement marking is one of the most efficient ways to help drivers feel safe and make the parking process easier and faster.

Proper pavement striping and signage increase traffic safety. They direct cars and pedestrians in the right direction, for example, to free parking spaces, spaces for disabled, loading zones, fire lanes, etc. 
 
In order to create a sense of safety, parking lot owners are obliged to care about all the details in the parking area. The parking lot maintenance includes high-quality painting and repainting of pavement marking. Parking lots should be laid-out and painted in accordance with appropriate codes and regulations, including ADA compliance issues.
​
Parking Lot Elements

• Line Striping (single, double or solid/skip lines dividing a parking area into spaces, designating entrance and exit)
• Handicap Logos (ensuring the safety of disabled utilizing the lot)
• Traffic Stencils (arrows, stops)
• Curb Painting (curb painting helps to distinguish the difference between the road and pavement).
• Well-maintained parking area marked with crisp, precise lines creates a good impression of the image of the company which makes customers come again and again.

 
Standard Colors for Pavement Markings
 
Parking lot maintenance companies offer a wide of services among which are pavement marking striping and re-striping. When talking about colors, each type of pavement markings should conform to the standard specified in the “Color Specifications for Retro reflective Sign and Pavement Marking Materials”.

There Are Four Main Colors for Pavement Markings

• Yellow pavement marking designates loading zones, no parking, and visitor parking areas. Yellow paint is also used for lines that separate opposing flows of traffic.
• White pavement markings in the parking lot mark transverse markings (crosswalks, words, symbols). Also, white lines separate one-way traffic lanes or mark their right edge.
• Pavement markings painted red designate one-way roadways, ramps, and others. In parking lots, red is used to forbid parking in fire lanes and no parking zones.
• Blue is used to emphasize handicap parking spaces a minimum number of which must be calculated separately for each parking lot according to ADA compliance standards. 

​
Painted Lines In Parking Lot get worn out and fade over time. To look fresh, parking lot lines and markings need to be repainted every 1 to 2 years. Weather conditions, traffic volume, quality of the asphalt and paint contribute to the durability of parking lot markings.

​The pavement markings in outdoor parking lots are much easier to get worn because of continuous sunlight, water, salt, and oil exposure. 

​
​CALL TODAY FOR A FREE QUOTE
Striping Parking Lots For Wildwood, Missouri
(314) 582-8849

​Chesterfield is a western suburb of St. Louis and is the largest city in west St. Louis County, Missouri.  As of the 2010 census the population is 47,484. Chesterfield celebrated its 30th birthday in 2018.
Parts of Chesterfield is located in the floodplain of the Missouri River, now known as Chesterfield Valley.  Chesterfield Valley is the location of Spirit of St. Louis Airport, used for corporate aviation, as well as the longest outdoor strip mall in America. 

There are many reasons to install speed bumps or humps in your parking lot.

• Creates convenient walking passages for pedestrians therefore raised in regions with a high frequency of people crossing from one side to the other. 
• Cost-effectiveness- speed bumps are cost-effective to install when incorporated into parking lot construction. Parking lots should provide adequate safety to all those who come to use. This is a major factor that clients consider when visiting parking areas. The safety aspects are immeasurable, but this does not rule out the need to think about cost when installing the speed bumps in the parking lots to ensure compliance with ADA regulations. 
• Decreasing traffic- speed bumps help in redirecting traffic. Many people love to drive at high speed; hence, they will always avoid areas with speed bumps. This helps in reducing traffic in parking lots with speed bumps. 
• Slow traffic- speed bumps are required where speeding is an issue, an issue that puts parking lot user’s safety and the installed structures at risk. Speed bumps force motorists to slow down whether the users like it or not. They minimize and eliminate damages to their vehicles. 
• Safety- speed bumps provide guaranteed safety to parking lot customers. Pedestrians bind parking lot areas and other motorists, hence the international regulations require speed bumps to be installed in all parking lots to help reduce accidents. 
• Speed bumps slow down drainage of rainwater from flowing into neighboring yards. 
• Noise reduction- when the volumes of traffic together with their speed are reduced, noise levels come to a reduction. 
• Keeping crosswalks safe- driving too fast in parking lots increases pedestrian’s accidents hence parking lot should be installed with speed bumps in areas that receive high foot traffic. 

How Speed Bumps Offer Safety  

• Reflective rubber speed bumps are painted yellow to increase visibility during the night time; this enhances pedestrian safety when they are at the crossing areas. 
• The parking lot owner should ensure speed bumps are installed to ensure drivers slow down to maintain safe parking conditions for drivers and pedestrians. 
• Accident prevention- speed bumps are raised in front of the facility entrances so vehicles are forced to slow down for pedestrians to pass. Usually, the drivers are expected to drive at the set speed limit. 
• Reinforces the speed limit-failing to indicate speed limit signs, drivers are expected to operate at 5 mph. When drivers move at a higher speed than expected, then the speed bumps are installed to ensure they slow down to ensure safety for all. 
• Speed bumps force drivers to slow down. The parking lot is usually unsafe when drivers move at a faster speed. The drivers should be aware of existing pedestrians, cars that exit and the installed structures that provide proper communication for safety standards expected. 

CALL TODAY FOR A FREE QUOTE
Striping Parking Lots For Chesterfield, Missouri
(314) 582-8849

​Glendale is a suburb of St. Louis with a population of 5,919. Glendale is one of the best places to live in Missouri and is in St. Louis County.  Residents of Glendale have a rural feel and most residents own their homes.  There are a lot of restaurants, coffee shops, and parks in Glendale.  Many families in Glendale are conservative.  The school district in Glendale is highly rated.

• ​Grant’s Farm
• Forest Park
• Ulysses S. Grant National Historic Site
• The Magic House - Saint Louis Children’s Museum
• National Museum of Transportation
• Saint Louis Zoo
• Saint Louis Science Center
• Saint Louis Art Museum
• The Gateway Arch

•  Installation and Replacement

Sometimes parking lots seem to be quite disorganized. A parking lot usually has many sections for different categories of drivers. For this reason, there is a need to point out each of them in which space or section drivers can and cannot park. A variety of parking signs can be installed around the parking area. For this, parking lot operators should find out which signs are the most common and which are required to be installed in the parking lots. 

• Metal Signs For Your Parking Lot

When choosing among the most common parking sign materials, buyers prefer steel and aluminum as the cheapest and most reliable options.
​
While the first material that comes to mind when mentioning the word “metal” is iron, manufacturers don't use it for parking signs for its vulnerability. Despite the fact that iron is one of the most affordable materials, it is easy to get rusted which is a significant drawback. In past, steel was used to prevent rust on iron signs but steel is quite heavy comparing to iron, hence less suitable for posting and installing. Aluminum is three times lighter than steel which allows using aluminum signs of different thicknesses. 

When thinking which metal signs are required to be placed in or around your parking lot, take into consideration that it depends on the number of sections and categories of drivers.  Customers are offered a wide variety of pre-designed signs as well as possible to order metal signs for any specific use. The most common signs installed in the parking lots are stop signs, No Parking sign, fire lane sign and other.  Parking sign manufacturers produce a huge number of signs based on the type of material, its thicknesses, and other parameters. For today, metal parking signs are known to be the most popular ones because of their durability.  

CALL TODAY FOR A FREE QUOTE
Striping Parking Lots For Glendale, Missouri
(314) 582-8849

There are a number of guidelines you must keep in mind, despite the fact that there are no standards regarding how far apart bollards should be placed. Bollards should be spaced in such a way that your goal will be accomplished--barring unnecessary traffic from entering a particular area. At the same time, you don't want to space them too close together otherwise they will create new problems. Bollards placed to control traffic and vehicle access should be spaced to fit nearly all vehicles or none at all.


Areas with multi-channels are required to be managed correctly to protect your employees, customers, and other assets are one of many possible circumstances. The way you place Bollards can forbid vehicles access and still let pedestrians flow through easily. As a rule of thumb in bollard installation service, it is suggested that the spacing between every Bollard should not be greater than 5 feet. This is because an average-sized car is about 6 feet in width. Hence, this prevents vehicles from driving through the gaps between the Bollards. This is very important when you are deciding on how far apart bollards should be placed in your parking lot. Bollards installed to control the flow of traffic should be spaced no less than 3 feet apart so that it will meet the accessibility requirements of the ADA or Americans with Disability Act, but not more than 5 feet apart, to block the minimum width of a vehicle.

Are bollards required in every parking lot?  
Bollards are not required but are recommended for every parking lot because they help when it comes to preventing accidents in parking lots. Bollard installation is one of the effective steps to take to guarantee safety on your business property.

Depending on your needs, you can install solid bollards, flexible bollards or retractable bollards in your parking lot.
 

• Solid Bollards – they are installed permanently into the substrate of the parking lot.  Solid bollards are made of steel filled with concrete and painted in glowing colors like yellow to make them more noticeable. The purpose of these bollards is to offer a tough barrier against vehicle owners that try to park or drive in unauthorized areas.   

 

• Flexible Bollards – These bollard types are used on an as-required basis.  Flexible bollards bend when struck by a vehicle. Therefore, they offer a bit of prevention for those who might drive dangerously.  Furthermore, they are an ideal solution due to their affordability. In addition, they are lightweight in construction, keeping them from damaging vehicles when struck.

• Retractable Bollards – You can raise or lower retractable bollards as needed in the course of certain events or times of the day. These parking bollards are perfect for use in parking lots with changing layouts.

Additionally, the city contains many different types of businesses that all need parking lot striping, and we are proud to have provided our services to this great city previously. If you are looking to get your Ballwin parking lot striped, or if you have any other parking lot needs, be sure to give us a call at (314) 582 - 8849.

Parking lot striping is very important for the following reasons:

1. Safety Reasons
Line striping is the way to go if you are looking out for the safety of pedestrians and drivers that pass through your parking area on a daily basis. Parking lot pavement markings direct traffic flow so that stop signs, one-way streets, and other vital safety signs are supported by well-marked pavement signs, helping drivers to maneuver through the lot safely.

Moreover, cars understand how to move through the parking lot correctly when the parking lot lines are well-marked on your pavement. This means less time figuring out a disorganized lot and more time on your business premises.  

2. Parking Lot Striping Maximizes Parking Spaces
Clearly marked line stalls on asphalt pavement guarantee that the highest number of trucks and cars can park in the at once. In addition, it prevents the parking lots from being blocked off or becoming jam-packed by unlawfully parked vehicles.

3. Maintains Curb Appeal
The curb appeal of your facility is maintained by a newly striped parking lot. The combination of black pavement and crisp white, with yellow and blue lines, which is mostly used in parking lot markings and parking lot line striping is quite charming.

4. Ensures Proper Access for Handicapped
Handicapped spacing and access is an imperative aspect of line striping. Parking lot striping makes it easier for handicap visitors to navigate in the handicap parking spaces or parking lot and direct visitors to the straightest course to the building. Public facilities and businesses are also required by law to clearly designate handicap spots.

​When you are installing or repairing line striping in your parking lot, hiring a professional parking lot striping contractor might not look like an essential cost. You may believe that you will save a huge sum of money when you do it all alone. But how tough could it be to stripe your parking lot by yourself? 
 
Sure, you have watched more than a few YouTube videos on how to paint the lines in your parking lot and you are now confident in your abilities. But, the truth is that there are some tasks that need to be left for the professionals, despite the fact that you may the best handyman in the world.